How To Install Roll Roofing With Nails

December 24, 2021

227

Nail And Cement The Roll Roofing

Roll roofing installation, Flat roof installation step by step ,must watch!

Nail the roofing using a sturdy hammer, leave 9-12 inches of space between nails. Use a minimum of 1-inch roofing nails to make sure it will remain steady. Press down the edges, ensuring that it won’t take off easily.

Repeat the process for the next few levels of the roof, start again from step 2 and measure the roof again. When reaching the top, cover the nail heads with cement to make sure they are sealed.

As for the sides with shorter width, start off with a 6-inch overlap and repeat just like before.

How To Install Roll Roofing

Many building supplies stores throughout the Delaware Valley sell roll roofing. The material is similar in composition to asphalt shingles but thinner. Many homeowners with do-it-yourself experience can quickly learn how to install roll roofing. It is appropriate for low-pitch roofs, like those on sheds, gazebos, or three-seasons rooms. To avoid working with stiff and brittle material, we suggest you choose a day for your project when it is at least 50 degrees.

Plan The Roll Roofing Job

Plan the roofing job, the job sequence, the purchase of materials, and be sure you have all needed materials on hand before starting the job. The basic roofing sequence is

Inspect the condition of the existing roof and roof decking

Plan and schedule any demolition, removal of materials that must precede the new roof installation

Have roof protection tarps or other materials if the roof might be left open and incomplete across inclement weather

Measure the roof and calculate the materials and supplies needed: roofing, underlayment, lap sealant, flashings, nails

Install roofing underlayment

Install finish flashings or counter flashings where required

Don’t Miss: Remove Contacts With Long Nails

Additional Tips For Installing Roll Roofing

A few roll roofing additional details include:

Try to install the roll roofing material when the temperature is at least 50°F.

Clean the area of any sticks and stones beforehand and as you work. Also, install a drip edge along the edge of the roof.
With lower sloped roofs, you can install the material horizontally. With higher-sloped roofs, you should install them vertically.

Vents That Are Sealed

Apply roofing cement together around the plumbing outlet to seal it. Cut a 2-foot-wide hole in the middle of the roofing as well as slip it across the pipe. Each piece should be at least 4 sizes bigger than the lower course. Drill a hole inside the roll sheeting and cover it with it. Cement two roofing sections together. Add a startup flashing for extra security.

Recommended Reading: How To Remove Powder Nails Without Acetone

Preparing To Add Rolled Roofing

1David BitanRoofing Contractor & Maintenance ProfessionalExpert Interview. 14 July 2020. If you can, get a friend or someone else to help you. Use a long measuring tape. If your roof is rectangular or square on either side, it’s easy to work out the measurements. Measure the length and width and multiply them to find the area of the roof.XResearch source

If your roof is not uniform and has different sections of different sizes, measure 1 section at a time. Multiply each length and width to find the area of each section.

Add the section areas together to find the total area of the roof.

Get an extra 5-10% of material to account for overhangs and overlap.

2Purchase the appropriate amount of rolled roofing. Go to your local hardware or building supplies store and ask for enough rolled roofing to fit the area of your roof. Rolled roofing comes in rolls, much like carpet. You can cut the roll to fit corners and other areas.XResearch sourceAdvertisement

3Take proper safety precautions when you’re on your roof. For safety purposes, it’s a good idea to have someone with you when you’re walking around on a roof. Never go up on your roof when it’s wet or if rain is forecast. Roofs become very slippery when wet. Even when it’s dry, watch your footing and move slowly when walking on a slanted roof.XResearch source

Wear footwear with proper grip on the soles. Don’t go up on your roof with canvas shoes or sneakers on.

If you have gutters, clear them out with gloves and a bucket.

S And Instructions For How To Install Roll Roofing

Do you know how to install roll roofing? Roll roofing is put over exposed wood sheathing as well as sheeting that has been primed. The sheathing would be better protected against dampness and leaks if roofing felt is applied first. Employ roll roofing as a cost-effective roof solution. Installing this material is simple and just takes basic carpentry abilities.

Choose roll roofing for such a practical alternative when aesthetics isnt as crucial. Its built of materials comparable to composite shingles although its not as durable. Verify the guarantee, which may be limited to one year. Should last longer when you construct and how to install roll roofing that uses the double-coverage approach.

You can utilize the exposed-nail technique if the roofing is slanted. Use the shrouded approach for a slightly slanted roof. Have double coverage on some kind of flat or almost flat roof, while a torch-down thermoplastic polymer or EPDM roof would be a superior option.

Consider spending half a day constructing flashings as well as roll roofing for something like 700-square-foot roofing with minor issues, working with such a helper. Remove the old shingles from the roof and prepare for just a reroof simply ripping them off. Very basic carpentry qualifications are necessary to install such roofing material because it is the easiest of the roofing components to install.

Read Also: Do Gel Nails Damage Your Nails

Measure And Mark The Next Line Above The First Layer

You can continue and measure up 32 above the first layer, as youre going to place a part of the second layer on top of the first one.

You repeat the previous steps and apply the cement on the roof, but right below the second chalk line. When the cement is across the roof, you may continue with placing the second layer. Always have the first 6 in of the next layer on top of the previous layer.

As for the nailing, you should also be sure that the nail goes through the first and second layers at the same time.

How To Install Roll Roofing Instructions

Roll Roofing A Small Flat Roof with Greg Zanis

Measure the length and width of the roof surface. Multiply the numbers to determine how many rolls of roofing to buy. Increase the number by 5% to 10% to account for pieces that need to be trimmed.

Unroll the roofing material on the ground to relax some of the curl out of it.

Thoroughly clean dirt from the roof with a broom. If any nails are sticking up from the roof sheathing, drive them down with a hammer.

Use roofing cement to adhere the roof drip edge to bottom edge of roof deck.

Measure 35 inches up from the bottom edge. Mark it with a chalk line to create a straight line parallel to the drip edge.

Cut roll roofing with utility knife into sections that fit the roof.

Position the first piece along the chalk line. The other edge of the roll should line up with the outer edge of the drip edge.

Drive roofing nails along the bottom edge and along the sides. Place nails 1 inch from the edges and 6 inches apart.

Put down roof cement in a band 2 inches wide along the top edge of the first row.

Position the second row of roll roofing along the chalk line and overlap the roofing cement.

Nail the bottom edge of the second row the same way as before.

Repeat the process until the roof is complete.

Seal the final top edge with roofing cement.

Recommended Reading: Where To Buy Incoco Nail Strips

Attach The First & Second Sheets

To begin roofing, you should position the first course accurately so that it overhangs the drip edges and move it out to a calculated distance. Push the nails every 3 inches at one end of the rake, pull it taut, and push the nails further along the eave edge.

For a good installation, the nail should only be 1 inch from the edges, and for more protection, you could add a 3-foot wide strip on the 18-inches. When placing the second sheet, it should overlap the first by 4 inches, or you could use a different type of roll roofing to cover the area. Use a chalk line to indicate the top of the next sheet then, you can roll it along the line and push nails for the first sheet.

How Do You Install A Roll On A Flat Roof

How to do it

Roll Out Materials. Install drip-edge flashings, roofing felt, and WSU, if needed.

Attach First Course.

. In this regard, do you nail down roll roofing?

Nail the roofing in place with short roofing nails spaced 6 inches apart and 1 inch in from the outer edges of the roll roofing. Add a second piece of full-width roll roofing over the first. Nail it in place with roofing nails spaced 6 inches apart and placed 1 inch from the edge.

Likewise, how do you install rolled roofing over shingles? Before you begin, thoroughly clean the existing roof, removing any debris like leaves or sticks. Then, install a layer of roofing felt to provide a sturdy base for the new roll roofing. Once this has been done, the roll roofing can be installed in the same manner as if it were over bare roof sheathing.

Then, how do you install rolled roofing on a flat roof?

Part 2Installing the Rolled Roofing

Apply roofing cement to the roof.

Cut the rolled roofing to the right size using a razor knife.

Place the first layer of rolled roofing on the roof.

Hammer nails into the rolled roofing to secure it.

How do you install a rubber roof yourself?

Roof Deck Preparation. Clean the roof surface prior to installation.

Install Drip Batten. Install the Drip batten wherever a gutter is present.

Install Drip Back Drip Trim. The Drip Trim has a front and back piece.

Chase out Wall Upstand.

Don’t Miss: How To Remove Powder Nail Polish

What Are The Problems With Metal Roofs

4 Common Metal Roof Problems

Corrosion. When you have a galvalume or galvanized steel metal roof, you run the risk of rust and corrosion.
Failing Fastener. Fasteners and clips that hold your standing seam metal roof down are critical.
Scratches and Punctures. Debris from trees and snow can scuff your standing seam metal roof.

Fading Paint.

Prepare Roofing Material And Acquire Tools

To prepare the roll you will need to make sure it is warm enough for it to be malleable, it is recommended that you do not try and unroll the material if the temperature is under 40 degrees Fahrenheit. If it is too cold, the material is at risk of cracking or breaking. Ensure that the roll is warm enough to be pliable before continuing.

This is also a great time to gather the tools you will need. Ensure you have the below tools on hand before starting this project. I have provided a list below for the tools that you will need.

Rolled roofing

Underlay

Don’t Miss: Essie Gel How To

Overlap The Valley & Add The Final Piece

We are slowly getting to the end of the installation. The next step is to work from one side of the roof across the valleys center by 2 feet. Now on the other edge of the valley, you can overlay the valley, hit a chalk line, and gently trim the piece that is located at the center of the valley. While doing this, you should keep the nails 12 inches away from the center of the valley and use a 4-inch wide roofing cement bed to attach everything.

You can simply overlap the sheets at the ridge using the cement and nails for the final piece. But note that the last piece does not come down at least 8 inches past the ridge peak. Ensure that the peak embedded in the cement is well covered.

Installing Drip Edge Flashing

1Place drip edge flashing on the roof. Use the flashing to cover the outside edges of your roof. Knowing the roofs size can help you get the correct flashing length. If the roofs edges are longer than the flashing available for purchase, you can connect separate pieces together.

Check the labeling before choosing the flashing. Get wide flashing designed for use on flat roofs.XResearch source

2Cut the flashing to size with tin snips. Use a marker to note where the flashing extends beyond the roof. Trim through them, then place them back on the roof to make sure they are the correct size.XResearch source

3Attach the flashing with roofing nails placed every 8 in . Use galvanized nails since they are more resistant to water damage than regular nails. Choose nails that are long enough to penetrate the flashing and any roofing material already underneath it. Secure the flashing with nails placed about 1 in from the roofs edge.XResearch source

A good nail length to use is 1 12 in . Depending on your roof, you may need longer nails.

4Spray the flashing with a bitumen primer. Check the label on the primer before purchasing it. Make sure you choose something compatible with torch down roofing. To apply the primer, hold the spray nozzle about 6 in above the flashing. Move the nozzle across the flashing to coat them in an even, opaque layer of primer.XResearch source

Don’t Miss: Average Price For Dip Nails

Ask A Question Or Search Inspectapedia

Questions & answers or comments about roll roofing installation, life, leaks, repairs..

Try the search box just below, or if you prefer, post a question or comment in the box below and we will respond promptly.

Search the InspectApedia website

Note: appearance of your Comment below may be delayed:if your comment contains an image, web link, or text that looks to the software as if it might be a web link, your posting will appear after it has been approved by a moderator. Apologies for the delay.

Technical Reviewers & References

Installing The Rolled Roofing

Roofing – Installing Tarpaper Felt – The Basics – Dry in of Mockup

1 Using a measuring tape, measure 35 inches up from the bottom of the roof and make a mark with chalk. The measurement of 35 inches is the default measurement used by most roofing professionals. Use a ruler or meter stick to draw the chalk line across the roof.XResearch source

Avoid using eaves as guides as they are not necessarily placed at the same height across the roof.

2Apply roofing cement to the roof. Use a trowel to scoop up the roofing cement. Spread the roofing cement along the edges of your roof so itâs about 1â8â1â4 inch thick. You can get roofing cement at the local hardware or building supplies store.XResearch source

Apply the cement in stages. Do the bottom part of the roof before you start working on that section, apply it to the middle before you start working there, and so on. Use the chalk lines as the borders of each section.

Always wear gloves when working with roofing cement.

Read the instructions on the side of the roofing cement container before you begin.

3Cut the rolled roofing to the right size using a razor knife. The rolled roofing should reach the chalk line when you lay it down and should stretch from 1 side of the roof to the other. You’ll need to use plenty of pressure with the razor knife to cut the rolled roofing material.XResearch source

The first layer should cover the roof as far as the chalk line.

Be careful when working with a hammer and nails on a roof. Make sure you have a stable grip on the roof.

Read Also: How To Remove Nail Glue

How To Install Roll Roofing For Maximum Life

Nonetheless roll roofing installations will have a longer life if installed according to the product manufacturer’s instructions, nailed at proper intervals, and with seams properly sealed.

It’s also important to install roll roofing over a smooth sound roof deck.

If the roof decking sags, ponding on the roof surface after rain may reduce its life.

Overlapping strips of asphalt roll roofing are installed over the roof surfaces with overlapped edge joints sealed, usually with a heated asphalt compound, or cold-applied using a similar sealant that functions at lower temperatures.

Sketch courtesy of Carson Dunlop Associates.

Probably in part because asphalt roll roofing is typically used on low slope and nearly flat roofs, it can have an anticipated wear life of less than ten years, often five years.

The life of roll roofing may be extended by coatings.

Why Choose Roll Roofing

Roll roofing is very advantageous for any home or business owner, especially when using it for outbuildings that require a simple roof. Here are some of the pros:

The material is easy to transport, as it’s lightweight and rolled up.
It’s cost-effective, known as the most affordable roofing material you can purchase.

The roof is easy to install, with anyone being able to do it. It only takes a few minutes to roll out a square of roll roof.
Take note that roll roofing is great for low-inclined roofs, but not for flat ones.

Read Also: Is Kerasal Good For Nail Fungus

How To Install Rolled Roofing On A Flat Roof

Although rolled roofing is a cheap and easy-to-apply roofing material, failure to follow the required steps will lead to consequences like leakages and fast wear and tears. First, measure your flat roof to know what size of material you need to buy.

Measure the length and width, and ensure your roof does not have extra parts that will need a smaller material. After getting the correct measurements, purchase the roofing material in your local hardware or order from an online shop.

The next step is to prepare the roof for installation. Ensure you clean it by removing all the dirt and debris from the ceiling. Use a brush and leaf blower to ensure the cleanliness is thorough. Ensure you wear protective clothing to not fall from the roof.

Previous articleMay Credit Card Cho Tiem Nail

Next articleHow Are Nail Techs Paid