Saturday, March 23, 2024
HomeWhat Nails To Use For Vinyl Siding

What Nails To Use For Vinyl Siding

Before You Start: Prepare The Surface

Kaycan Vinyl Siding Installation Tips: Nailing
  • Securely nail all loose boards and wood trim and replace any rotted boards.
  • Scrape away old caulking around windows and doors. The build-up of old caulking interferes with the positioning of new trim for the siding.
  • Remove down-spouts, lighting fixtures, and mouldings where they will interfere with the siding installation.
  • Window sill extension may be cut off so new trim can be installed flush with the window casing.
  • Tie back shrubbery and trees where they are close to the wall. This will give you more room to work. It will also avoid damage to the landscaping.

Allow Space At Panel Ends As Well

Youll also need to leave a little extra room in spots when your siding abuts up against window trim, door frames, and other accessories. Its all due to the same principle: the siding needs a little room to spread out during the high heat of summer.

In this case, leave about a ¼ of an inch between the end of the siding panel and the trim. That will leave you with plenty enough room to cover the expansion.

How Long Should Nails Be For Siding

The length of your siding nails largely depends on the nature of your project. But, siding nails typically come in a size that ranges between 1.25-inches to 2.5-inches. You should always use at least a 1.5-inch nail for your siding projects to be safe. This length will handle the usual width of a siding board, which is .75-inches thick.

Don’t Miss: Best Polygel Kit For Beginners

Proper Type Of Nails For Vinyl Siding

I have a conventional 2 story home that I plan to have vinyl siding installed on. I plan on using a 1 Foam insulated sheathing under it. My question is: what type and size nail is best for this job. Aluminum nails bend too easily, so thats out. Will Galvanized be OK or should I opt for a galvanized hot dipped instead? What about stainless steel? Your comments appreciated.

  • |#2

    1 3/4″” roofers. Center the nails in the slots and dont nail em tight or you’ll get the siding to look like a roller coaster. Be consistant in your nailing. I usually nail every foot and a half or less. HAve the seams overlap so when you look down the side of the house you walk along most you dont see the butt ends. If your concerned about insulation ….besides the 1″ foam you can also use “slip in” foam behind each panel which I highly reccomend. Reason being is it makes each panel more solid besides the insulating factor, HAve fun tin man.

    BE well

  • Galvies will work fine for the vinyl, but if you are putting up any aluminum trim make sure you use aluminum nails.

    Do not try this at home!

    I am a trained professional!

  • |#6

    Galvanized nails and aluminum ANYTHING don’t mix.

    When two dissimilar metals are together, and ANY kind of moisture is introduced, you get corrosion. The corrosion is caused by a process caused electrolysis, andit WILL eat up the metal.

    Humidity, and moisture in the air are enough to eat at the metals and cause a problem.

    Just a thought…James DuHamel

  • Can You Nail Siding Into Osb

    Buy Grip

    When the correct fastening method is used, trim and siding can be directly attached to the nail -base structural sheathing. Thats true even if the siding is attached to plywood or OSB through a layer of non-structural continuous insulation.

    Recommended Reading: How To Treat Nail Fungus With Vicks

    What Nails Do I Use For Lp Smartside

    Nailing Requirements Using a nail gun makes quick work of installing LP SmartSide products. Youll want to use a minimum of. 113-inch shank diameter hot-dipped galvanized box-style nails with a minimum of 0.27-inch head diameter. The nails should be long enough to penetrate the structural framing by at least one inch.

    Vinyl Siding Installation Step #1: Window And Door Trim

    When you reach a window or door, cut away any caulk that might keep the new trim from laying flat against the existing molding. At windows, cut trim channel to match the length of the sill and then nail it into place.

    Cut two lengths of channel for the sides, allowing an extra 2 inches on each. At the bottom, make a 1-inch cut along the corner of the facing edge. Bend the wide surface of the channel inward at this cut to make a drip-edge tab and slide the tab under the sill channel. At the top of a window or door, cut off all but the face of the trim flush with the existing top molding, and nail the trim in place.

    Don’t Miss: Hongo Killer Nail Formula Review

    Dont Face Nails To Avoid Problems Down The Line

    Nails that are facedmeaning nailed directly on the surface of your sidingwill be visible when youre finished, which just doesnt look all that nice. Plus, they can cause siding to buckle as well. Nails should be fixed squarely in the middle of the slots at the end of each panel. That way, theyll be covered by the next panels overlap.

    Ideally, nails should go in about 1/32 of an inch from each panels edge, although you should read the manufacturers guidelines for the proper measurements.

    Keep your nails straight and give your vinyl siding a little room to breathe and you should be covered for the next 20 to 40 yearsall for the price of a little elbow grease!

    Find today’s best prices for your home improvement project.

    What Kinds Of Nails Are For Wood Siding

    Tip of the Week: Selecting a Fastener When Installing Vinyl Siding

    Related Articles

    Whether you install clapboard, T1-11, cedar shakes, or board-and-batten siding on your house, you can attach it with either nails or screws. Many builders choose nails because they’re easier to work with, especially from a ladder. The nails you choose must be weatherproof and long enough to prevent the siding from pulling out.

    Recommended Reading: How To Remove Contact Lenses With Nails

    Galvanized Roofing Nails Are Your Best Bet For Siding Success

    Its not surprising to hear that you need a galvanized nail on your homes exteriorafter all, regular fasteners could rust when exposed to the elements. Still, youll want to make sure that the nails you choose are strong enoughand long enoughto keep your siding from lifting off when the wind blows.

    Most builders agree that you should opt for roofing nails for this sort of project. Roofing nails have longer shanksbetween one and two inchesand a flatter nail head to keep the material below held securely in place. Theyre also extra sharp, so you wont have to work as hard to nail them in. Most contractors agree that nails used in siding projects should measure at least 1 ½ inches longor up to 2 ½ inches if youre installing backerboard with the siding. Nail heads require a 5/16 inches minimum in diameter. Nail shanks? At least inches in diameter.

    Additionally, a lot of contractors say not to use aluminum nails, since these may eventually bend. Galvanized nails are typically made from steel, which is a stronger material overall.

    How Do You Nail Vinyl Siding

    Start nailing vertical siding and trim pieces in the top of the uppermost slots to hold them in position. Place all other nails in the center of the slots. Space nails a maximum of 16 inches apart for horizontal siding panels, every 12 inches for vertical siding panels, and 6 to 12 inches for accessories.

    Don’t Miss: Strong Spice Destroys Nail Fungus

    Leaving Room To Move Is Key To Successful Vinyl Siding Installation

    Vinyl siding expands and contracts in warm and cold weather. It is important that the siding have enough flexibility to move as needed to prevent it from buckling. Siding has fairly wide pre-drilled holes for nailing. Use only these holes for nailing and never drive nails through the face of the siding. It is recommended that the nail be placed directly in the middle of the nail hole to give it space to move from side to side.

    When attaching your siding, its very important that the nail not be pounded in completely tight. Doing so prevents the vinyl siding from being able to slide left and right as intended. Use only galvanized or roofing nails that wont rust. You can also choose to use screws, as long as they also arent installed too tight.

    As you work your way up the wall, make sure the lip of each siding panel gently locks in to the one below it.

    Find more information and installation resources at the Vinyl Siding Institute.

    How Do You Hang Things On Vinyl Siding

    Maze Nails Maze Nails 249871 1.5 in. 1 lbs Aluminum Vinyl ...

    Fortunately, there are several methods that you can use to hang decorations on the side of your house that do not create any holes in your siding.

  • Hang a vinyl siding hook on your house. This is the most efficient method.
  • Attach a cup hook to the side of your house.
  • Hang a wire hook from the vinyl soffit trim.
  • You May Like: Nail Polish Off Fabric

    Vinyl Siding Installation: Materials And Tools

    While you can expect differences among manufacturers, siding systems generally include 12-foot lengths of siding, window/door trim channel, J-channel, utility channel, corner moldings, and metal starter strips. In addition, vented and unvented soffits, as well as fascia covers, are available.

    The siding must be installed over a flat surface, so unless you’re siding a new home, or have removed the old lap siding, you’ll need to line the wall with sheets of rigid-foam board, usually 1/2-inch thick. While rigid foam offers some insulation, its primary function is to provide a flat nailing surface. Both the rigid foam and siding can be nailed in place with galvanized shingle nails.

    Vinyl siding comes in several styles and in a variety of colors. We chose a Dutch lap style, which has the look of tongue-and-groove car siding, because of its distinctive profile.

    All vinyl siding and vinyl soffit and fascia can be cut with tin snips, a circular saw with a plywood blade, or by scoring it with a knife and breaking it.

    Vinyl Siding Installation Step #: Dealing With Obstructions

    If your home has a , it’s likely to be suspended from a wall and covering the bottom of the existing siding. In this case, you’ll need to maintain the starter-strip height on both sides of the deck and trim the siding to fit above the deck.

    Begin by installing the first row of siding on both sides of the deck. To provide a common reference point, measure up 8 inches from the top of this row and stretch a string line across the deck. Then, trim around the door leading onto the deck. Door and window trim that is about 1 1/4-inches deep will accommodate 1/2-inch insulation board as well as the 1/2-inch siding. Finally, measure the distance from the first row to the deck top and cut the siding to fit over the deck.

    To secure this trimmed length, nail J-channel along the top of the deck, backed by a strip of 1/2-inch plywood.

    Don’t Miss: How To Get Nail Polish Out Of Clothes Without Acetone

    What Kind Of Nails Do You Use On Vinyl Siding

    roofing

    . In this manner, can you put nails in vinyl siding?

    Nails should be centered and driven loosely into the nailing slots of vinyl or aluminum siding. Do not face nail. Face nailing is not only unsightly, but it will also cause vinyl to buckle with changes in temperature. Do not nail any siding parts too tight.

    Additionally, do you use nails or screws for siding? Fastener ChoicesUse aluminum, galvanized steel, or other corrosion-resistant nails, staples, or screws when installing vinyl siding. In such cases, the fastener will need to be long enough to penetrate through the non-nailable material and then 1 1/4 into wood framing or other nailable material.

    Additionally, how long should nails be for vinyl siding?

    Most contractors agree that nails used in siding projects should measure at least 1 ½ inches longor up to 2 ½ inches if you’re installing backerboard with the siding. Nail heads require a 5/16 inches minimum in diameter.

    How do you hang things on vinyl siding without nails?

    Fortunately, there are several methods that you can use to hang decorations on the side of your house that do not create any holes in your siding. Hang a vinyl siding hook on your house. This is the most efficient method. Slip the top of the hook underneath a piece of siding and wiggle it until it “snaps” into place.

    Why Proper Nailing Is So Important For Vinyl Siding

    How to Select Siding Nails

    Homes function best when every element works in perfect harmony. Even the smallest parts, like nails and screws, make a difference. But the type of nails you useand your nailing techniqueis extra important when you install vinyl siding on your home.

    Vinyl is a plastic product, so its a little bit more malleable than aluminum or woodparticularly when the sun is shining overhead. Unfortunately, that means its easy to get the nailing wrong. If you mess up and nail it too tight, the siding wont have room to expand when the weather heats up. Likewise, if you dont drive the nails in straight, the siding can buckle and ripple, as well.

    Dont let that put you off of vinyl, though. If you take care to install it properly, it can be a durable, attractive home cladding for years to come. Heres how to do it rightand avoid any buckles or ripples along the way.

    Recommended Reading: How Do You Get Nail Polish Out Of Carpet

    How To Replace A Damaged Panel

    To remove a panel for any reason, follow the steps below:

    • Slip a zip lock or unlocking tool behind the bottom lock of the panel above the one to be replaced and unzip it from the lock on the damaged panel.

    • Gently bend out upper panel. Take the nails out of the damaged panel and remove it.

    • Lock on the new panel and nail it up.

    • Use the unlocking tool again to zip the upper panel over the lock on the new panel.

    For more information, refer to page 38 of the VSI Vinyl Siding Installation Manual.

    Do Command Hooks Work On Vinyl Siding

    4.6/5CommandCommandcanvinyl sidingthe answer

    Hang a vinyl siding hook on your house. This is the most efficient method. Slip the top of the hook underneath a piece of siding and wiggle it until it “snaps” into place. This hooks it onto the bottom of the siding.

    Also Know, do Command hooks actually work? Command strips work on most surfaces, but not all. The surfaces you can use them on are painted, stained or varnished wood, glass, tile, painted cinder block, plaster, drywall, metal, and painted wallboard. They will also stick to smooth cinder block, like what you see inside school buildings.

    Accordingly, how do you hang something heavy on vinyl siding?

    Siding HooksThe easiest and safest way to hang something from vinyl siding is to use a siding hook. It slips into the groove between adjoining slats, and once it clicks into place, you can hang items as heavy as 12 pounds.

    Do Command hooks work outdoors?

    Using a new formulation of the revolutionary CommandAdhesive, these Outdoor Hooks are specially designed to hold strongly outdoors – they are water resistant, UV resistant, and can handle temperature extremes from -20 degrees F to 125 degrees F! Contains 1 large clear hook and 2 outdoor strips.

    You May Like: Does Dollar General Have Nail Polish

    Can You Nail Trim Into Drywall

    Use trim nails that will penetrate at least 1/2 inch into the studs. To choose the right-sized nail, add to that 1/2 inch the thickness of the drywall, usually 1/2inch, and the thickness of the trim board. Standard finish nails usually work fine. However, many carpenters prefer to use galvanized finish nails.

    What Nails Are Best For Vinyl Siding

    InterNACHI Inspection Graphics Library: Exterior » Vinyl ...

    Use aluminum, galvanized steel, or other corrosion-resistant nails, staples, or screws when installing vinyl siding. Aluminum trim pieces require aluminum or stainless steel fasteners. All fasteners must be able to penetrate a minimum of 1 1/4 into nailable material, such as wood sheathing and framing (Fig.

    Don’t Miss: How Much Do Nail Techs Make A Year

    How Long Will Non

    Non-galvanized nails lack a coat of zinc that protects them from exposure that results in rust. Treated lumbers are usually used in outdoor projects like decks or fences. So, if you use non-galvanized nails in treated lumber, its not a matter of if they will rust its just a matter of when. Many factors decide how quickly the nails will be ruined, like moisture and temperature. Depending on your environment, exposed non-galvanized nails can last less than two years, even in treated lumber.

    How Do You Nail Siding A House

    Snap each length of siding in place, so that its bottom lip hooks under the starter strip. Slide it into the corner and nail it every 16 in. or so. Be sure to center the nails in their slots to accommodate expansion.

    Consequently, how do you nail vinyl siding?

    Start nailing vertical siding and trim pieces in the top of the uppermost slots to hold them in position. Place all other nails in the center of the slots. Space nails a maximum of 16 inches apart for horizontal siding panels, every 12 inches for vertical siding panels, and 6 to 12 inches for accessories.

    Likewise, why do nails pop out of siding? There are a few reasons why nails pop out of siding: Expansion and contraction of the wood Fill the old nail holes with wood filler. If wood soaks up moisture and then dries out, it can warp or move.

    Likewise, what nails do you use for siding?

    Use electro, or hot-dipped galvanized steel or aluminum roofing type nails with a diameter of 1/8 and a nail head of 3/8 or larger. The nails should penetrate 3/4 into a solid wood base.

    What do you put under vinyl siding?

    To sum it up, house wrap is a lightweight, paper-like material that is most often used to completely cover the house, directly on top of the sheathing and behind the vinyl siding. Its primary purpose is to prevent air and water leaks that may have seeped past the vinyl exterior.

    You May Like Also

    Recommended Reading: How To Get Dipped Nails Off

    RELATED ARTICLES

    Popular Articles

    How To Get Healthy Nails